Insulate the dog house first, then add heat
A heater in a drafty dog house pours warmth out through the gaps. A raised floor and insulated walls keep your dog’s own body heat inside, and they let any heater you add later work less hard.
Why the house comes first
A dog curled up in a well-built house warms the air around it with its own body. A house that leaks lets that heat escape as fast as the dog makes it, and a heater then works against the gaps all night.
Fixing the house costs once and then runs free. It also cuts what a heater costs to run, which our running cost guide works out in kWh.
Start with the right size
A house just large enough for your dog to stand up and turn around keeps body heat better, according to the Humane Society of the United States. Every bit of extra space is extra air for the dog to warm.
If the house is far too big, an inner partition or a smaller sleeping box can help. Our guide on sizing a dog house heater shows how to measure the space in cubic feet.
Raise the floor
Cold, damp ground draws heat out of a floor around the clock. Raising the floor off the ground, as the HSUS and the ASPCA advise, stops that and keeps the floor out of puddles and snowmelt.
Pallets, bricks or treated lumber runners all work, as long as the house sits stable. Then insulate under the floor too, because that is where a lying dog presses its whole body.
Insulate the walls and the roof
Rigid foam board fits between the frame or against the inside walls of a wooden house. The higher its R-value, the better it resists heat flowing through, and thicker boards rate higher.
Always cover the foam with plywood or hard paneling. Dogs chew foam, and swallowed pieces can be dangerous, so no insulation should be left exposed inside.
The roof matters as much as the walls, since warm air rises. A lid that lifts off for cleaning can take its own layer of board, sealed at the edges.
- Rigid foam board: the most common choice, always covered so the dog can’t reach it
- Reflective foil insulation: thin and light, useful in plastic houses where boards won’t fit
- A second wall of plywood with an air gap, for a simple upgrade without foam
- A rubber mat under the straw, as an extra layer on the floor
Plastic, wood or igloo houses
A wooden house is the easiest to insulate, because foam board fits between the frame and plywood covers it. Screws hold well, and a heater can go on any covered wall later.
A plastic house has thin walls with little space for boards. Reflective foil insulation or thin foam glued to the inside, then covered with a hard panel, adds warmth without making the house too cramped.
Igloo-style houses are round, so flat boards don’t fit and the door is often wide. Concentrate on a raised base and a heavy door flap, and use the separate bracket Akoma sells if you add a Hound Heater.
Stop the drafts at the door
Face the door away from the prevailing wind. That one move costs nothing and keeps the wind out of the sleeping area.
Add a door flap of heavy vinyl or rubber strips, so your dog can push through while the warm air stays in. An offset entry or a short inner wall shields the bed even more.
Seal gaps in the corners and around the roof with outdoor caulk, but leave a small vent high on one wall. A dog breathes out moisture all night, and a sealed box turns damp and cold.
Bedding that stays dry
The HSUS recommends straw for outdoor bedding, not blankets or hay, which hold moisture. Straw stays loose and dry, and the dog can burrow into it.
Replace it when it gets damp or flattened. Our guide on keeping a dog house warm without electricity covers straw and self-warming beds in more detail.
Keep water and food bowls outside the sleeping area, so spills don’t soak the bedding. Check that the water has not frozen at least twice a day in hard cold.
When to add heat
Once the house is insulated and dry, watch how your dog copes. Most dogs are fine above about 45 °F, while below about 32 °F the small, short-coated, very young, old or sick ones need protection.
Every dog outdoors faces a risk of hypothermia and frostbite once it drops below about 20 °F. Our guide on how cold is too cold sets out those thresholds, and in dangerous cold the answer is bringing your dog inside.
When you do add heat, an insulated house lets a modest heater or a 60 W pad do the job. The homepage buying guide helps you decide which dog house heater to buy, and our brand guide covers who makes them.
Insulation and a heater together
A heater still needs space around it, so keep foam and its covering clear of the grille and follow the manual’s clearances. Mount it on a covered wall, never on bare foam board.
An insulated house also holds heat after the thermostat clicks off, so the heater cycles less often. That is where the savings on the power bill come from.
Our things to sort before you buy list on the homepage adds the details people tend to miss. Most of them cost little and pay back every cold night.
Adjustable heat for an insulated house
The Briidea 400W has a thermostat you set anywhere from 32 to 122 °F, so a well-insulated house can run at a low setting. Its fan runs five more minutes after the set point, then stops, and it has fewer owner reviews than the older names.